[lyra The Skala 하이엔드 카트리지]

lyra The Skala 하이엔드 카트리지

상품 옵션
판매가격
전화문의
원산지
일본
제조사
lyra
브랜드
lyra
수량
수량증가 수량감소

lyra The Skala mc

 

 

 

 

 

The Skala is the first of LYRA designer Jonathan Carr’s 5th-generation cartridge designs. At first sight the Skala appears to be made entirely of plastic, one of our distributors has even described it as a “formless white plastic blob!” However, we don’t mind (not too much, anyway). The Skala is a thoroughbred design focused on delivering pure performance.

Close inspection of the Skala gradually reveals a central structure consisting of a vertical metal blade that carries the cantilever system, the magnets and the output pins, i.e. the entire functional core of the cartridge. The blade is clamped against the tonearm headshell by an outer white plastic base into which are drilled the mounting screw holes. Looking from the rear, you can see that the vertical blade passes right through the base and makes direct contact with the headshell. Since the cantilever system is also mounted directly to the blade, the cantilever has, in effect, a seamless connection path to the tonearm.

The metal blade of the Skala in effect functions without the resonant carapace of a traditional shell, in addition to being “nude” like the other Lyra designs.

The small contact “footprint” of the blade focuses the force imparted by the mounting screws, creating a high-pressure contact area which forms a more rigid bond between Skala and tonearm headshell than the larger mounting surface of a conventional cartridge could provide. The white plastic base forces the vertical metal blade of the Skala against the tonearm’s headshell, and serves to constrain and damp resonances in the blade, and to reduce conductive material in the total body structure reducing eddy currents.

Although the plastic base is pretty much flush with the metal blade where contact is made with the headshell, the plastic will compress under pressure, while the blade will not. This allows a limited degree of azimuth adjustment to be made by the careful application of different amounts of torque to left and right mounting screws. Extreme care should be taken to tighten both mounting screws gradually and evenly, a little at a time. Over cranking one screw and then doing the same for the other could result in an unintentional change to the azimuth. The drilled holes in the plastic body are themselves lined with metal jackets to receive the mounting screws securely.

The magnetic system in the Skala is the same non-polepiece twin-disc direct-magnet system also used in most other LYRA models. However the body shape has been even more heavily carved away in the area of the magnet than any previous model– even more than on the Titan. This results in fewer eddy currents in a very sensitive area of the cartridge. New elements are a new non-conductive and non-magnetic front magnet carrier, a new cantilever system, a new output pin design, and a new output-pin carrier. The stylus guard is the same grooved slide-on type that has proven so successful on the other LYRA models.

Specifications:

  • Designer: Jonathan Carr
  • Builder: Yoshinori Mishima
  • Type: Medium weight, medium compliance, low-impedance moving coil cartridge
  • Stylus: Lyra-designed long-footprint variable-radius line-contact nude diamond (3um x 70um), slot-mounted
  • Cantilever system: Solid boron rod with short one-point wire suspension, directly mounted into cartridge vertical pillar
  • Coils: 2-layer deep, 6N high-purity copper, square-shaped chemically-purified high-purity iron former, 5.4ohm self-impedance, 9.1uH inductance
  • Output voltage: 0.5mV@5cm/sec., zero to peak, 45 degrees (CBS test record, other test records may alter results)
  • Frequency range: 10Hz ~ 50kHz
  • Channel separation: 35dB or better at 1kHz
  • Compliance: Approx. 12 x 10-6cm/dyne at 100Hz
  • Vertical tracking angle: 20 degrees
  • Cartridge body: Two-piece composite structure, each piece controlling resonances within the other: Vertical “pillar” is one-piece machining from spring-grade phosphor bronze solid billet, with reduced-surface higher-pressure headshell contact area; horizontal “body” is one-piece machining from high-loss polymer, with threaded brass inserts for mounting screws
  • Cartridge mounting screws: 2.6mm 0.45 pitch JIS standard
  • Distance from mounting holes to stylus tip: 9.5mm
  • Cartridge weight (without stylus cover): 9g
  • Recommended tracking force: 1.65 ~ 1.75g
  • Recommended load directly into MC phono input: 95.3ohm ~ 816ohm (determine by listening)
  • Recommended load via step-up transformer: 5 ~ 15ohm (step-up transformer’s output must be connected to 10kohm ~ 47kohm MM-level RIAA input, preferably via short, low-capacitance cable)
  • Recommended tonearms: High-quality pivoted or linear (tangential) tonearms with rigid bearing(s), adjustable anti-skating force, preferably VTA adjustment
 
배송은 주문 당일 배송을 원칙으로 하며 받으실 때까지 약 2-3일 정도 소요됩니다. (도서 산간지역 3-4일 소요)
•제품 수급에 의해 지연이 되는 경우 별도의 연락을 드린 후 배송을 하여 드립니다.
_ 전 제품 5만원 초과 상품은 배송비가 무료입니다.
(중고/전시품란의 일부상품 제외. 5만원 이하 상품은 3,000원의 배송비가 추가됩니다. )
_ 전제품 품질보증서가 들어있는 정식 수입원 제품입니다.
(일부 상품은 정식 수입품이지만 시리얼넘버로 정품관리를 하기 때문에 보증서가 들어있지 않을 수도 있습니다.)
-「전자상거래법 제17조 제1항」 에 의거하여 소비자의 단순변심으로도 7일 이내 청약철회가 가능합니다.
_제품을 설치하였거나 개봉후에는 반품 및 교환이 불가능합니다.
_제품 자체에 결함이 있을 경우 100% 교환 및 환불이 가능합니다.
_특별할인판매 및 기타 이벤트 판매의 경우 현금 주문은 24시간 이내에 입금되지 않으면 주문은 자동취소됩니다.
제품 개봉 및 설치를 하셨을 경우에는 공정거래위원회 표준약관 제15조 2항에 의거하여 교환 및 반품/환불이 불가능합니다.

 
review 리스트
번호
제목
작성자
작성일
조회
등록된 리뷰가 없습니다.
review 작성 폼
review board
이 름 :
평점 :      
내 용 :
review 리스트
이름
내용
평점
날짜
QnA 리스트
번호
제목
작성자
작성일
조회
등록된 문의가 없습니다.
비밀번호 확인 닫기